23.01.2017,12:09:12,$HST:Application just created
23.01.2017,12:09:12,$HST:SW-version 1.18, e-Callisto
23.01.2017,12:09:12,$HST:Configurationfile read
23.01.2017,12:09:12,$HST:Switched to automatic
23.01.2017,12:09:12,$HST:ATmega16 pre-configured
23.01.2017,12:09:12,$HST:Frequencyfile frq01005.cfg
23.01.2017,12:09:12,$HST:Callisto ready now...
23.01.2017,12:09:13,$HST:Measurement idle
23.01.2017,12:09:13,$HST:File scheduler.cfg read
23.01.2017,12:09:13,$HST:Measurement enable
23.01.2017,12:09:13,$CRX:AGC gain = 2.43V
23.01.2017,12:09:13,$CRX:Emitter BF199 = 0.14V
23.01.2017,12:09:13,$CRX:Analog Input = 9.24
23.01.2017,12:09:18,$HST:File frq01005.cfg read
23.01.2017,12:09:18,$HST:No calibration file found
23.01.2017,12:09:18,$HST:Plot buffer erased...
23.01.2017,12:09:18,$HST:Parametrisation RCU
23.01.2017,12:09:19,$CRX:ChargePump=On
23.01.2017,12:09:19,$HST:CD1316LV/IV detected
23.01.2017,12:09:19,$CRX:Debug=Off
23.01.2017,12:09:19,$CRX:Trigger=Extern
23.01.2017,12:09:19,$CRX:FPUcodex=2
23.01.2017,12:09:19,$CRX:GS =61765
23.01.2017,12:09:19,$CRX:GA =253
23.01.2017,12:09:19,$CRX:Delay=0msec
23.01.2017,12:09:19,$CRX:Frequency=45.0MHz
23.01.2017,12:09:19,$HST:Receiver connected
23.01.2017,12:09:19,$CRX:Sweeplength=200
23.01.2017,12:09:19,$CRX:low_band_max=171MHz
23.01.2017,12:09:19,$CRX:mid_band_max=450MHz
23.01.2017,12:09:19,$CRX:high_band_max=863MHz
23.01.2017,12:09:19,$CRX:Idle=0x
23.01.2017,12:09:19,$CRX:ChargePump=On
23.01.2017,12:09:19,$HST:CD1316LV/IV detected
23.01.2017,12:09:19,$CRX:Debug=Off
23.01.2017,12:09:19,$CRX:Trigger=Extern
23.01.2017,12:09:19,$CRX:FPUcodex=2
23.01.2017,12:09:19,$CRX:GS =61765
23.01.2017,12:09:19,$CRX:GA =624
23.01.2017,12:09:19,$CRX:Delay=0msec
23.01.2017,12:09:19,$CRX:Frequency=45.0MHz
23.01.2017,12:09:19,$HST:Receiver connected
23.01.2017,12:09:19,$CRX:Sweeplength=200
23.01.2017,12:09:19,$CRX:low_band_max=171MHz
23.01.2017,12:09:19,$CRX:mid_band_max=450MHz
23.01.2017,12:09:19,$CRX:high_band_max=863MHz
23.01.2017,12:09:19,$CRX:Idle=0x
23.01.2017,12:09:19,$HST:Switched to manual
23.01.2017,12:09:23,$HST:XY plot selected
23.01.2017,12:09:30,$HST:Param. RCU due to START
23.01.2017,12:09:30,$HST:Actual focuscode 02
23.01.2017,12:09:30,$HST:Enable data transfer
23.01.2017,12:09:30,$HST:Receiver calibration
23.01.2017,12:09:30,$CRX:Started
23.01.2017,12:09:30,$HST:Start new FITS-file
23.01.2017,12:09:30,$HST:Continous measurement
23.01.2017,12:26:47,$HST:XYZ plot selected
24.01.2017,00:00:00,$HST:Midnight -> memo cleared
24.01.2017,00:00:00,$HST:EOF(logfile)