28.04.2017,08:30:25,$HST:Application just created
28.04.2017,08:30:25,$HST:SW-version 1.18, e-Callisto
28.04.2017,08:30:25,$HST:Configurationfile read
28.04.2017,08:30:25,$HST:Switched to automatic
28.04.2017,08:30:25,$HST:ATmega16 pre-configured
28.04.2017,08:30:25,$HST:Frequencyfile frq01005.cfg
28.04.2017,08:30:25,$HST:Callisto ready now...
28.04.2017,08:30:26,$HST:Measurement idle
28.04.2017,08:30:26,$HST:File scheduler.cfg read
28.04.2017,08:30:26,$HST:Measurement enable
28.04.2017,08:30:26,$CRX:AGC gain = 2.42V
28.04.2017,08:30:26,$CRX:Emitter BF199 = 0.14V
28.04.2017,08:30:26,$CRX:Analog Input = 9.24
28.04.2017,08:30:32,$HST:File frq01005.cfg read
28.04.2017,08:30:32,$HST:No calibration file found
28.04.2017,08:30:32,$HST:Plot buffer erased...
28.04.2017,08:30:32,$HST:Parametrisation RCU
28.04.2017,08:30:32,$CRX:ChargePump=On
28.04.2017,08:30:32,$HST:CD1316LV/IV detected
28.04.2017,08:30:32,$CRX:Debug=Off
28.04.2017,08:30:32,$CRX:Trigger=Extern
28.04.2017,08:30:32,$CRX:FPUcodex=2
28.04.2017,08:30:32,$CRX:GS =3383
28.04.2017,08:30:32,$CRX:GA =253
28.04.2017,08:30:32,$CRX:Delay=0msec
28.04.2017,08:30:32,$CRX:Frequency=45.0MHz
28.04.2017,08:30:32,$HST:Receiver connected
28.04.2017,08:30:32,$CRX:Sweeplength=200
28.04.2017,08:30:32,$CRX:low_band_max=171MHz
28.04.2017,08:30:32,$CRX:mid_band_max=450MHz
28.04.2017,08:30:32,$CRX:high_band_max=863MHz
28.04.2017,08:30:32,$CRX:Idle=0x
28.04.2017,08:30:32,$CRX:ChargePump=On
28.04.2017,08:30:32,$HST:CD1316LV/IV detected
28.04.2017,08:30:32,$CRX:Debug=Off
28.04.2017,08:30:32,$CRX:Trigger=Extern
28.04.2017,08:30:32,$CRX:FPUcodex=2
28.04.2017,08:30:32,$CRX:GS =3383
28.04.2017,08:30:32,$CRX:GA =624
28.04.2017,08:30:32,$CRX:Delay=0msec
28.04.2017,08:30:32,$CRX:Frequency=45.0MHz
28.04.2017,08:30:32,$HST:Receiver connected
28.04.2017,08:30:32,$CRX:Sweeplength=200
28.04.2017,08:30:32,$CRX:low_band_max=171MHz
28.04.2017,08:30:32,$CRX:mid_band_max=450MHz
28.04.2017,08:30:32,$CRX:high_band_max=863MHz
28.04.2017,08:30:32,$CRX:Idle=0x
28.04.2017,08:30:38,$HST:scheduler.cfg watched
28.04.2017,08:30:42,$HST:XY plot selected
28.04.2017,08:30:46,$HST:Param. RCU due to START
28.04.2017,08:30:46,$HST:Actual focuscode 02
28.04.2017,08:30:46,$HST:Enable data transfer
28.04.2017,08:30:46,$HST:Receiver calibration
28.04.2017,08:30:46,$CRX:Started
28.04.2017,08:30:47,$HST:Start new FITS-file
28.04.2017,08:30:47,$HST:Continous measurement
28.04.2017,11:59:58,$HST:Measurement stop
28.04.2017,11:59:58,$HST:Measurement wait...
28.04.2017,11:59:58,$HST:EOT (&) detected
28.04.2017,11:59:58,$HST:Measurement halted
28.04.2017,11:59:58,$HST:Measurement stop
28.04.2017,11:59:58,$CRX:Stopped
28.04.2017,11:59:58,$HST:Measurement wait...
28.04.2017,11:59:59,$HST:Measurement halted
28.04.2017,11:59:59,$HST:Measurement idle
28.04.2017,11:59:59,$CRX:Stopped
28.04.2017,12:00:00,$HST:Autostart via scheduler
28.04.2017,12:00:00,$HST:Param. RCU due to START
28.04.2017,12:00:00,$HST:Actual focuscode 02
28.04.2017,12:00:00,$CRX:AGC gain = 2.42V
28.04.2017,12:00:00,$CRX:Emitter BF199 = 0.14V
28.04.2017,12:00:00,$CRX:Analog Input = 9.24
28.04.2017,12:00:00,$HST:Enable data transfer
28.04.2017,12:00:00,$HST:Receiver calibration
28.04.2017,12:00:00,$CRX:Started
28.04.2017,12:00:00,$HST:Start new FITS-file
28.04.2017,12:00:00,$HST:Continous measurement
28.04.2017,18:44:58,$HST:Measurement stop
28.04.2017,18:44:58,$HST:Measurement wait...
28.04.2017,18:44:58,$HST:EOT (&) detected
28.04.2017,18:44:58,$HST:Measurement halted
28.04.2017,18:44:58,$HST:Measurement stop
28.04.2017,18:44:58,$CRX:Stopped
28.04.2017,18:44:58,$HST:Measurement wait...
28.04.2017,18:44:59,$HST:Measurement halted
28.04.2017,18:44:59,$HST:Measurement idle
28.04.2017,18:44:59,$CRX:Stopped
28.04.2017,18:45:00,$HST:Measurement enable
28.04.2017,18:45:00,$CRX:AGC gain = 2.42V
28.04.2017,18:45:00,$CRX:Emitter BF199 = 0.14V
28.04.2017,18:45:00,$CRX:Analog Input = 9.24
28.04.2017,18:45:01,$HST:No more entries in scheduler.
29.04.2017,00:00:00,$HST:Midnight -> memo cleared
29.04.2017,00:00:00,$HST:EOF(logfile)