01.01.2018,11:47:07,$HST:Application just created
01.01.2018,11:47:07,$HST:SW-version 1.23, e-Callisto
01.01.2018,11:47:07,$HST:Configurationfile read
01.01.2018,11:47:07,$HST:Switched to automatic
01.01.2018,11:47:07,$HST:ATmega16 pre-configured
01.01.2018,11:47:07,$HST:Frequencyfile frq01005.cfg
01.01.2018,11:47:07,$HST:Callisto ready now...
01.01.2018,11:47:07,$HST:Measurement idle
01.01.2018,11:47:07,$HST:File scheduler.cfg read
01.01.2018,11:47:07,$HST:Measurement enable
01.01.2018,11:47:07,$CRX:AGC gain = 2.42V
01.01.2018,11:47:07,$CRX:Emitter BF199 = 0.14V
01.01.2018,11:47:07,$CRX:Analog Input = 9.24
01.01.2018,11:47:10,$HST:File FRQ01005.CFG read
01.01.2018,11:47:10,$HST:No calibration file found
01.01.2018,11:47:10,$HST:Plot buffer erased...
01.01.2018,11:47:10,$HST:Parametrisation RCU
01.01.2018,11:47:10,$CRX:ChargePump=On
01.01.2018,11:47:10,$HST:CD1316LV/IV detected
01.01.2018,11:47:10,$CRX:Debug=Off
01.01.2018,11:47:10,$CRX:Trigger=Extern
01.01.2018,11:47:10,$CRX:FPUcodex=2
01.01.2018,11:47:10,$CRX:GS =3397
01.01.2018,11:47:10,$CRX:GA =253
01.01.2018,11:47:10,$CRX:Delay=0msec
01.01.2018,11:47:10,$CRX:Frequency=45.0MHz
01.01.2018,11:47:10,$HST:Receiver connected
01.01.2018,11:47:10,$CRX:Sweeplength=200
01.01.2018,11:47:10,$CRX:low_band_max=171MHz
01.01.2018,11:47:10,$CRX:mid_band_max=450MHz
01.01.2018,11:47:10,$CRX:high_band_max=863MHz
01.01.2018,11:47:10,$CRX:Idle=0x
01.01.2018,11:47:10,$CRX:ChargePump=On
01.01.2018,11:47:10,$HST:CD1316LV/IV detected
01.01.2018,11:47:10,$CRX:Debug=Off
01.01.2018,11:47:10,$CRX:Trigger=Extern
01.01.2018,11:47:10,$CRX:FPUcodex=2
01.01.2018,11:47:10,$CRX:GS =3397
01.01.2018,11:47:10,$CRX:GA =624
01.01.2018,11:47:10,$CRX:Delay=0msec
01.01.2018,11:47:10,$CRX:Frequency=45.0MHz
01.01.2018,11:47:10,$HST:Receiver connected
01.01.2018,11:47:10,$CRX:Sweeplength=200
01.01.2018,11:47:10,$CRX:low_band_max=171MHz
01.01.2018,11:47:10,$CRX:mid_band_max=450MHz
01.01.2018,11:47:10,$CRX:high_band_max=863MHz
01.01.2018,11:47:10,$CRX:Idle=0x
01.01.2018,11:47:12,$HST:File FRQ01005.CFG read
01.01.2018,11:47:12,$HST:No calibration file found
01.01.2018,11:47:12,$HST:Plot buffer erased...
01.01.2018,11:47:12,$HST:Parametrisation RCU
01.01.2018,11:47:12,$CRX:ChargePump=On
01.01.2018,11:47:12,$HST:CD1316LV/IV detected
01.01.2018,11:47:12,$CRX:Debug=Off
01.01.2018,11:47:12,$CRX:Trigger=Extern
01.01.2018,11:47:12,$CRX:FPUcodex=2
01.01.2018,11:47:12,$CRX:GS =3397
01.01.2018,11:47:12,$CRX:GA =624
01.01.2018,11:47:12,$CRX:Delay=0msec
01.01.2018,11:47:12,$CRX:Frequency=45.0MHz
01.01.2018,11:47:12,$HST:Receiver connected
01.01.2018,11:47:12,$CRX:Sweeplength=200
01.01.2018,11:47:12,$CRX:low_band_max=171MHz
01.01.2018,11:47:12,$CRX:mid_band_max=450MHz
01.01.2018,11:47:12,$CRX:high_band_max=863MHz
01.01.2018,11:47:12,$CRX:Idle=0x
01.01.2018,11:47:12,$CRX:ChargePump=On
01.01.2018,11:47:12,$HST:CD1316LV/IV detected
01.01.2018,11:47:12,$CRX:Debug=Off
01.01.2018,11:47:12,$CRX:Trigger=Extern
01.01.2018,11:47:12,$CRX:FPUcodex=2
01.01.2018,11:47:12,$CRX:GS =3397
01.01.2018,11:47:12,$CRX:GA =624
01.01.2018,11:47:12,$CRX:Delay=0msec
01.01.2018,11:47:12,$CRX:Frequency=45.0MHz
01.01.2018,11:47:12,$HST:Receiver connected
01.01.2018,11:47:12,$CRX:Sweeplength=200
01.01.2018,11:47:12,$CRX:low_band_max=171MHz
01.01.2018,11:47:12,$CRX:mid_band_max=450MHz
01.01.2018,11:47:12,$CRX:high_band_max=863MHz
01.01.2018,11:47:12,$CRX:Idle=0x
01.01.2018,11:47:13,$HST:Yt plot selected
01.01.2018,11:47:25,$HST:Switched to manual
01.01.2018,11:47:26,$HST:Param. RCU due to START
01.01.2018,11:47:26,$HST:Actual focuscode 02
01.01.2018,11:47:26,$HST:Enable data transfer
01.01.2018,11:47:26,$HST:Receiver calibration
01.01.2018,11:47:26,$CRX:Started
01.01.2018,11:47:26,$HST:Start new FITS-file
01.01.2018,11:47:27,$HST:Continous measurement
02.01.2018,00:00:00,$HST:Midnight -> memo cleared
02.01.2018,00:00:00,$HST:EOF(logfile)