27.09.2018,11:18:40,$HST:Application just created
27.09.2018,11:18:40,$HST:SW-version 1.23, e-Callisto
27.09.2018,11:18:40,$HST:Configurationfile read
27.09.2018,11:18:40,$HST:Switched to automatic
27.09.2018,11:18:40,$HST:ATmega16 pre-configured
27.09.2018,11:18:40,$HST:Frequencyfile frq00255.cfg
27.09.2018,11:18:40,$HST:Callisto ready now...
27.09.2018,11:18:41,$HST:Measurement idle
27.09.2018,11:18:41,$HST:File scheduler.cfg read
27.09.2018,11:18:41,$HST:Measurement enable
27.09.2018,11:18:41,$CRX:AGC gain = 1.59V
27.09.2018,11:18:41,$CRX:Emitter BF199 = 0.13V
27.09.2018,11:18:41,$CRX:Analog Input = 9.24
27.09.2018,11:18:47,$HST:File FRQ00255.CFG read
27.09.2018,11:18:47,$HST:No calibration file found
27.09.2018,11:18:47,$HST:Plot buffer erased...
27.09.2018,11:18:47,$HST:Parametrisation RCU
27.09.2018,11:18:47,$CRX:ChargePump=On
27.09.2018,11:18:47,$HST:CD1316LV/IV detected
27.09.2018,11:18:47,$CRX:Debug=Off
27.09.2018,11:18:47,$CRX:Trigger=Soft
27.09.2018,11:18:47,$CRX:FPUcodex=2
27.09.2018,11:18:47,$CRX:GS =61764
27.09.2018,11:18:47,$CRX:GA =253
27.09.2018,11:18:47,$CRX:Delay=2msec
27.09.2018,11:18:47,$CRX:Frequency=870.0MHz
27.09.2018,11:18:47,$HST:Receiver connected
27.09.2018,11:18:47,$CRX:Sweeplength=200
27.09.2018,11:18:47,$CRX:low_band_max=171MHz
27.09.2018,11:18:47,$CRX:mid_band_max=450MHz
27.09.2018,11:18:47,$CRX:high_band_max=863MHz
27.09.2018,11:18:47,$CRX:Idle=0x
27.09.2018,11:18:47,$CRX:ChargePump=On
27.09.2018,11:18:47,$HST:CD1316LV/IV detected
27.09.2018,11:18:47,$CRX:Debug=Off
27.09.2018,11:18:47,$CRX:Trigger=Extern
27.09.2018,11:18:47,$CRX:FPUcodex=2
27.09.2018,11:18:47,$CRX:GS =61764
27.09.2018,11:18:47,$CRX:GA =624
27.09.2018,11:18:47,$CRX:Delay=2msec
27.09.2018,11:18:47,$CRX:Frequency=45.0MHz
27.09.2018,11:18:47,$HST:Receiver connected
27.09.2018,11:18:47,$CRX:Sweeplength=200
27.09.2018,11:18:47,$CRX:low_band_max=171MHz
27.09.2018,11:18:47,$CRX:mid_band_max=450MHz
27.09.2018,11:18:47,$CRX:high_band_max=863MHz
27.09.2018,11:18:47,$CRX:Idle=0x
27.09.2018,12:04:05,$HST:Yt plot selected
27.09.2018,12:04:06,$HST:Param. RCU due to START
27.09.2018,12:04:06,$HST:Actual focuscode 02
27.09.2018,12:04:06,$HST:Enable data transfer
27.09.2018,12:04:06,$HST:Continuous measurement
27.09.2018,12:04:06,$CRX:Started
27.09.2018,12:04:06,$HST:Start new FITS-file
27.09.2018,12:04:06,$HST:Continous measurement
27.09.2018,12:04:12,$HST:XY plot selected
27.09.2018,12:15:46,$HST:Measurement stop
27.09.2018,12:15:46,$HST:FITS #1 200rows x 2800cols
27.09.2018,12:15:46,$HST:Measurement wait...
27.09.2018,12:15:46,$HST:EOT (&) detected
27.09.2018,12:15:47,$HST:Measurement halted
27.09.2018,12:15:47,$HST:Measurement idle
27.09.2018,12:15:47,$CRX:Stopped
27.09.2018,12:15:47,$HST:Measurement enable
27.09.2018,12:15:47,$CRX:AGC gain = 1.59V
27.09.2018,12:15:47,$CRX:Emitter BF199 = 0.13V
27.09.2018,12:15:47,$CRX:Analog Input = 9.24
27.09.2018,12:15:48,$HST:All threads terminated
27.09.2018,12:15:48,$HST:This application closed