31.10.2018,12:50:16,$HST:Application just created
31.10.2018,12:50:16,$HST:SW-version 1.23, e-Callisto
31.10.2018,12:50:16,$HST:Configurationfile read
31.10.2018,12:50:16,$HST:Switched to automatic
31.10.2018,12:50:16,$HST:ATmega16 pre-configured
31.10.2018,12:50:16,$HST:Frequencyfile frq01090.cfg
31.10.2018,12:50:16,$HST:Callisto ready now...
31.10.2018,12:50:17,$HST:Measurement idle
31.10.2018,12:50:17,$HST:File scheduler.cfg read
31.10.2018,12:50:17,$HST:Measurement enable
31.10.2018,12:50:17,$CRX:AGC gain = 2.49V
31.10.2018,12:50:17,$CRX:Emitter BF199 = 0.15V
31.10.2018,12:50:17,$CRX:Analog Input = 9.24
31.10.2018,12:50:23,$HST:File FRQ01090.CFG read
31.10.2018,12:50:23,$HST:No calibration file found
31.10.2018,12:50:23,$HST:Plot buffer erased...
31.10.2018,12:50:23,$HST:Parametrisation RCU
31.10.2018,12:50:23,$CRX:ChargePump=On
31.10.2018,12:50:23,$HST:CD1316LV/IV detected
31.10.2018,12:50:23,$CRX:Debug=Off
31.10.2018,12:50:23,$CRX:Trigger=Extern
31.10.2018,12:50:23,$CRX:FPUcodex=3
31.10.2018,12:50:23,$CRX:GS =3396
31.10.2018,12:50:23,$CRX:GA =253
31.10.2018,12:50:23,$CRX:Delay=0msec
31.10.2018,12:50:23,$CRX:Frequency=45.0MHz
31.10.2018,12:50:23,$HST:Receiver connected
31.10.2018,12:50:23,$CRX:Sweeplength=200
31.10.2018,12:50:23,$CRX:low_band_max=171MHz
31.10.2018,12:50:23,$CRX:mid_band_max=450MHz
31.10.2018,12:50:23,$CRX:high_band_max=863MHz
31.10.2018,12:50:23,$CRX:Idle=0x
31.10.2018,12:50:23,$CRX:ChargePump=On
31.10.2018,12:50:23,$HST:CD1316LV/IV detected
31.10.2018,12:50:23,$CRX:Debug=Off
31.10.2018,12:50:23,$CRX:Trigger=Extern
31.10.2018,12:50:23,$CRX:FPUcodex=3
31.10.2018,12:50:23,$CRX:GS =3396
31.10.2018,12:50:23,$CRX:GA =624
31.10.2018,12:50:23,$CRX:Delay=0msec
31.10.2018,12:50:23,$CRX:Frequency=45.0MHz
31.10.2018,12:50:23,$HST:Receiver connected
31.10.2018,12:50:23,$CRX:Sweeplength=200
31.10.2018,12:50:23,$CRX:low_band_max=171MHz
31.10.2018,12:50:23,$CRX:mid_band_max=450MHz
31.10.2018,12:50:23,$CRX:high_band_max=863MHz
31.10.2018,12:50:23,$CRX:Idle=0x
31.10.2018,12:50:41,$HST:XY plot selected
31.10.2018,12:50:44,$HST:Param. RCU due to START
31.10.2018,12:50:44,$HST:Actual focuscode 03
31.10.2018,12:50:44,$HST:Enable data transfer
31.10.2018,12:50:44,$HST:Receiver calibration
31.10.2018,12:50:44,$CRX:Started
31.10.2018,12:50:45,$HST:Start new FITS-file
31.10.2018,12:50:45,$HST:Continous measurement
31.10.2018,12:50:50,$HST:XYZ plot selected
31.10.2018,13:05:46,$HST:FITS #1 200rows x 3600cols
31.10.2018,13:20:46,$HST:FITS #2 200rows x 3600cols
31.10.2018,13:35:46,$HST:FITS #3 200rows x 3600cols
31.10.2018,13:50:46,$HST:FITS #4 200rows x 3600cols
31.10.2018,14:05:46,$HST:FITS #5 200rows x 3600cols
31.10.2018,14:20:46,$HST:FITS #6 200rows x 3600cols
31.10.2018,14:35:46,$HST:FITS #7 200rows x 3600cols
31.10.2018,14:50:46,$HST:FITS #8 200rows x 3600cols
31.10.2018,15:05:46,$HST:FITS #9 200rows x 3600cols
31.10.2018,15:20:46,$HST:FITS #10 200rows x 3600cols
31.10.2018,15:35:46,$HST:FITS #11 200rows x 3600cols
31.10.2018,15:50:46,$HST:FITS #12 200rows x 3600cols
31.10.2018,16:05:46,$HST:FITS #13 200rows x 3600cols
31.10.2018,16:20:46,$HST:FITS #14 200rows x 3600cols
31.10.2018,16:35:46,$HST:FITS #15 200rows x 3600cols
31.10.2018,16:50:46,$HST:FITS #16 200rows x 3600cols
31.10.2018,17:05:45,$HST:FITS #17 200rows x 3600cols
31.10.2018,17:20:46,$HST:FITS #18 200rows x 3600cols
31.10.2018,17:35:45,$HST:FITS #19 200rows x 3600cols
31.10.2018,17:50:45,$HST:FITS #20 200rows x 3600cols
31.10.2018,18:05:45,$HST:FITS #21 200rows x 3600cols
31.10.2018,18:20:45,$HST:FITS #22 200rows x 3600cols
31.10.2018,18:35:45,$HST:FITS #23 200rows x 3600cols
31.10.2018,18:44:58,$HST:Measurement stop
31.10.2018,18:44:58,$HST:FITS #24 200rows x 2210cols
31.10.2018,18:44:58,$HST:Measurement wait...
31.10.2018,18:44:58,$HST:EOT (&) detected
31.10.2018,18:44:58,$HST:Measurement halted
31.10.2018,18:44:58,$HST:Measurement stop
31.10.2018,18:44:58,$CRX:Stopped
31.10.2018,18:44:58,$HST:Measurement wait...
31.10.2018,18:44:59,$HST:Measurement halted
31.10.2018,18:44:59,$HST:Measurement idle
31.10.2018,18:44:59,$CRX:Stopped
31.10.2018,18:45:00,$HST:Measurement enable
31.10.2018,18:45:00,$CRX:AGC gain = 2.49V
31.10.2018,18:45:00,$CRX:Emitter BF199 = 0.15V
31.10.2018,18:45:00,$CRX:Analog Input = 9.24
31.10.2018,18:45:01,$HST:No more entries in scheduler.
01.11.2018,00:00:00,$HST:Midnight -> memo cleared
01.11.2018,00:00:00,$HST:EOF(logfile)