23.04.2021,07:57:45,$HST:Application just created
23.04.2021,07:57:45,$HST:SW-version 1.24, e-Callisto
23.04.2021,07:57:45,$HST:Configurationfile read
23.04.2021,07:57:45,$HST:Switched to automatic
23.04.2021,07:57:45,$HST:ATmega16 pre-configured
23.04.2021,07:57:45,$HST:Frequencyfile frq00470.cfg
23.04.2021,07:57:45,$HST:Callisto ready now...
23.04.2021,07:57:45,$HST:Measurement idle
23.04.2021,07:57:46,$HST:File scheduler.cfg read
23.04.2021,07:57:46,$HST:Measurement enable
23.04.2021,07:57:46,$CRX:AGC gain = 3.98V
23.04.2021,07:57:46,$CRX:Analog Input = 5.10
23.04.2021,07:57:52,$HST:File FRQ00470.CFG read
23.04.2021,07:57:52,$HST:No calibration file found
23.04.2021,07:57:52,$HST:Plot buffer erased...
23.04.2021,07:57:52,$HST:Parametrisation RCU
23.04.2021,07:57:58,$HST:File FRQ00470.CFG read
23.04.2021,07:57:58,$HST:No calibration file found
23.04.2021,07:57:58,$HST:Plot buffer erased...
23.04.2021,07:57:58,$HST:Parametrisation RCU
23.04.2021,07:59:58,$HST:Measurement stop
23.04.2021,07:59:58,$HST:Measurement wait...
23.04.2021,07:59:59,$HST:Measurement halted
23.04.2021,07:59:59,$HST:Measurement idle
23.04.2021,07:59:59,$HST:Measurement enable
23.04.2021,08:00:00,$HST:Autostart via scheduler
23.04.2021,08:00:00,$HST:Param. RCU due to START
23.04.2021,08:00:00,$HST:Actual focuscode 02
23.04.2021,08:00:00,$HST:Enable data transfer
23.04.2021,08:00:00,$HST:Continuous measurement
23.04.2021,08:00:00,$HST:Start new FITS-file
23.04.2021,08:00:00,$HST:Continous measurement
23.04.2021,09:18:16,$CRX:e-Callisto ETH Zurich
23.04.2021,09:18:16,$HST:Watchdog triggered -> Reset
23.04.2021,09:18:16,$CRX:V1.8 / 2012-04-02
23.04.2021,09:18:16,$HST:Found LO=25.43 MHz
23.04.2021,09:18:16,$CRX:V1.8 / 2012-04-02
23.04.2021,09:18:16,$HST:Found LO=25.43 MHz
23.04.2021,09:18:16,$CRX:Debug=Off
23.04.2021,09:18:16,$CRX:Trigger=No
23.04.2021,09:18:16,$CRX:FPUcodex=0
23.04.2021,09:18:16,$CRX:GS =0
23.04.2021,09:18:16,$CRX:GA =0
23.04.2021,09:18:16,$CRX:Delay=0msec
23.04.2021,09:18:16,$CRX:Frequency=0.0MHz
23.04.2021,09:18:16,$HST:Receiver connected
23.04.2021,09:18:16,$CRX:Sweeplength=0
23.04.2021,09:18:16,$CRX:low_band_max=171MHz
23.04.2021,09:18:16,$CRX:mid_band_max=450MHz
23.04.2021,09:18:16,$CRX:high_band_max=863MHz
23.04.2021,09:18:16,$CRX:Idle=0
23.04.2021,09:18:16,$CRX:V1.8 / 2012-04-02
23.04.2021,09:18:16,$HST:Found LO=25.43 MHz
23.04.2021,09:18:16,$CRX:Debug=Off
23.04.2021,09:18:16,$CRX:Trigger=Intern
23.04.2021,09:18:16,$CRX:FPUcodex=0
23.04.2021,09:18:16,$CRX:GS =107
23.04.2021,09:18:16,$CRX:GA =0
23.04.2021,09:18:16,$CRX:Delay=0msec
23.04.2021,09:18:16,$CRX:Frequency=45.0MHz
23.04.2021,09:18:16,$HST:Receiver connected
23.04.2021,09:18:16,$CRX:Sweeplength=200
23.04.2021,09:18:16,$CRX:low_band_max=171MHz
23.04.2021,09:18:16,$CRX:mid_band_max=450MHz
23.04.2021,09:18:16,$CRX:high_band_max=863MHz
23.04.2021,09:18:16,$CRX:Idle=0
23.04.2021,09:18:19,$HST:Auto stop due to data loss.
23.04.2021,09:18:19,$HST:Measurement stop
23.04.2021,09:18:19,$HST:Measurement wait...
23.04.2021,09:18:20,$HST:Measurement halted
23.04.2021,09:18:20,$HST:Measurement idle
23.04.2021,09:18:20,$CRX:Stopped
23.04.2021,09:18:20,$HST:Measurement enable
23.04.2021,09:18:20,$CRX:AGC gain = 3.96V
23.04.2021,09:18:20,$CRX:Emitter BF199 = 0.13V
23.04.2021,09:18:20,$CRX:Analog Input = 16.48
23.04.2021,09:18:22,$HST:Check RS232-connection!
23.04.2021,09:18:25,$HST:Attempting Auto-Start
23.04.2021,09:18:25,$HST:Param. RCU due to START
23.04.2021,09:18:25,$HST:Actual focuscode 02
23.04.2021,09:18:25,$HST:Enable data transfer
23.04.2021,09:18:25,$HST:Continuous measurement
23.04.2021,09:18:25,$CRX:Started
23.04.2021,09:18:26,$HST:Start new FITS-file
23.04.2021,09:18:26,$HST:Continous measurement
23.04.2021,09:23:43,$HST:Yt plot selected
23.04.2021,09:23:44,$HST:XY plot selected
23.04.2021,09:23:44,$HST:XYZ plot selected
23.04.2021,11:59:58,$HST:Measurement stop
23.04.2021,11:59:58,$HST:Measurement wait...
23.04.2021,11:59:58,$HST:EOT (&) detected
23.04.2021,11:59:58,$HST:Measurement halted
23.04.2021,11:59:58,$HST:Measurement stop
23.04.2021,11:59:58,$CRX:Stopped
23.04.2021,11:59:59,$HST:Measurement wait...
23.04.2021,11:59:59,$HST:Measurement halted
23.04.2021,11:59:59,$HST:Measurement idle
23.04.2021,11:59:59,$CRX:Stopped
23.04.2021,12:00:00,$HST:Measurement enable
23.04.2021,12:00:00,$CRX:AGC gain = 3.97V
23.04.2021,12:00:00,$CRX:Emitter BF199 = 0.13V
23.04.2021,12:00:00,$CRX:Analog Input = 16.48
23.04.2021,12:00:00,$HST:Autostart via scheduler
23.04.2021,12:00:00,$HST:Param. RCU due to START
23.04.2021,12:00:00,$HST:Actual focuscode 02
23.04.2021,12:00:00,$HST:Enable data transfer
23.04.2021,12:00:00,$HST:Continuous measurement
23.04.2021,12:00:00,$CRX:Started
23.04.2021,12:00:00,$HST:Start new FITS-file
23.04.2021,12:00:00,$HST:Continous measurement
23.04.2021,15:59:58,$HST:Measurement stop
23.04.2021,15:59:58,$HST:Measurement wait...
23.04.2021,15:59:58,$HST:EOT (&) detected
23.04.2021,15:59:58,$HST:Measurement halted
23.04.2021,15:59:58,$HST:Measurement stop
23.04.2021,15:59:58,$CRX:Stopped
23.04.2021,15:59:59,$HST:Measurement wait...
23.04.2021,15:59:59,$HST:Measurement halted
23.04.2021,15:59:59,$HST:Measurement idle
23.04.2021,15:59:59,$CRX:Stopped
23.04.2021,16:00:00,$HST:Measurement enable
23.04.2021,16:00:00,$CRX:AGC gain = 3.98V
23.04.2021,16:00:00,$CRX:Emitter BF199 = 0.13V
23.04.2021,16:00:00,$CRX:Analog Input = 16.48
23.04.2021,16:00:00,$HST:Autostart via scheduler
23.04.2021,16:00:00,$HST:Param. RCU due to START
23.04.2021,16:00:00,$HST:Actual focuscode 02
23.04.2021,16:00:00,$HST:Enable data transfer
23.04.2021,16:00:00,$HST:Continuous measurement
23.04.2021,16:00:00,$CRX:Started
23.04.2021,16:00:00,$HST:Start new FITS-file
23.04.2021,16:00:00,$HST:Continous measurement
23.04.2021,19:28:37,$HST:Measurement stop
23.04.2021,19:28:37,$HST:EOT (&) detected
23.04.2021,19:28:37,$HST:Measurement wait...
23.04.2021,19:28:37,$HST:Measurement halted
23.04.2021,19:28:37,$HST:Measurement idle
23.04.2021,19:28:37,$CRX:Stopped
23.04.2021,19:28:38,$HST:Measurement enable
23.04.2021,19:28:38,$CRX:AGC gain = 3.98V
23.04.2021,19:28:38,$CRX:Emitter BF199 = 0.13V
23.04.2021,19:28:38,$CRX:Analog Input = 16.48
23.04.2021,19:28:42,$HST:Manual frequencyfile sel.
23.04.2021,19:28:48,$HST:File c:\callisto-02\application\FRQ00470.CFG read
23.04.2021,19:28:48,$HST:No calibration file found
23.04.2021,19:28:48,$HST:Plot buffer erased...
23.04.2021,19:28:48,$HST:Parametrisation RCU
23.04.2021,19:28:48,$CRX:V1.8 / 2012-04-02
23.04.2021,19:28:48,$HST:Found LO=25.43 MHz
23.04.2021,19:28:48,$CRX:Debug=Off
23.04.2021,19:28:48,$CRX:Trigger=Intern
23.04.2021,19:28:48,$CRX:FPUcodex=2
23.04.2021,19:28:48,$CRX:GS =107
23.04.2021,19:28:48,$CRX:GA =0
23.04.2021,19:28:48,$CRX:Delay=0msec
23.04.2021,19:28:48,$CRX:Frequency=45.0MHz
23.04.2021,19:28:48,$HST:Receiver connected
23.04.2021,19:28:48,$CRX:Sweeplength=200
23.04.2021,19:28:48,$CRX:low_band_max=171MHz
23.04.2021,19:28:48,$CRX:mid_band_max=450MHz
23.04.2021,19:28:48,$CRX:high_band_max=863MHz
23.04.2021,19:28:48,$CRX:Idle=0
23.04.2021,19:28:48,$CRX:V1.8 / 2012-04-02
23.04.2021,19:28:48,$HST:Found LO=25.43 MHz
23.04.2021,19:28:48,$CRX:Debug=Off
23.04.2021,19:28:48,$CRX:Trigger=Intern
23.04.2021,19:28:48,$CRX:FPUcodex=2
23.04.2021,19:28:48,$CRX:GS =107
23.04.2021,19:28:48,$CRX:GA =0
23.04.2021,19:28:48,$CRX:Delay=0msec
23.04.2021,19:28:48,$CRX:Frequency=45.0MHz
23.04.2021,19:28:48,$HST:Receiver connected
23.04.2021,19:28:48,$CRX:Sweeplength=200
23.04.2021,19:28:48,$CRX:low_band_max=171MHz
23.04.2021,19:28:48,$CRX:mid_band_max=450MHz
23.04.2021,19:28:48,$CRX:high_band_max=863MHz
23.04.2021,19:28:48,$CRX:Idle=0
23.04.2021,19:28:49,$HST:Param. RCU due to START
23.04.2021,19:28:49,$HST:Actual focuscode 02
23.04.2021,19:28:49,$HST:Enable data transfer
23.04.2021,19:28:49,$HST:Continuous measurement
23.04.2021,19:28:49,$CRX:Started
23.04.2021,19:28:49,$HST:Start new FITS-file
23.04.2021,19:28:50,$HST:Continous measurement
23.04.2021,19:59:58,$HST:Measurement stop
23.04.2021,19:59:58,$HST:EOT (&) detected
23.04.2021,19:59:58,$HST:Measurement wait...
23.04.2021,19:59:58,$HST:Measurement halted
23.04.2021,19:59:58,$HST:Measurement stop
23.04.2021,19:59:58,$CRX:Stopped
23.04.2021,19:59:58,$HST:Measurement wait...
23.04.2021,19:59:59,$HST:Measurement halted
23.04.2021,19:59:59,$HST:Measurement idle
23.04.2021,19:59:59,$CRX:Stopped
23.04.2021,19:59:59,$HST:Measurement enable
23.04.2021,19:59:59,$CRX:AGC gain = 3.97V
23.04.2021,19:59:59,$CRX:Emitter BF199 = 0.13V
23.04.2021,19:59:59,$CRX:Analog Input = 16.48
23.04.2021,20:00:00,$HST:Autostart via scheduler
23.04.2021,20:00:00,$HST:Param. RCU due to START
23.04.2021,20:00:00,$HST:Actual focuscode 02
23.04.2021,20:00:00,$HST:Enable data transfer
23.04.2021,20:00:00,$HST:Continuous measurement
23.04.2021,20:00:00,$CRX:Started
23.04.2021,20:00:00,$HST:Start new FITS-file
23.04.2021,20:00:00,$HST:Continous measurement
23.04.2021,20:00:01,$HST:No more entries in scheduler.
24.04.2021,00:00:00,$HST:Midnight -> memo cleared
24.04.2021,00:00:00,$HST:EOF(logfile)